AN778 Implementing the External Memory Interface on PIC18C601/801 MCUs Author: Gaurang Kavaiya Microchip Technology Inc. INTRODUCTION The PIC18C601 and PIC18C801 are the very first members of Microchip's PIC18 family that are ROMless microcontrollers -- that is, they have no on-chip program memory. Both offer the enhanced PIC18 architecture, along with the ability to use different types and sizes of external program memory to exactly fit any application. In addition to standard 1.5 Kbytes of general purpose RAM, the PIC18C601 can address up to 256 Kbytes of external program memory, while the PIC18C801 can address up to 2 Mbytes of external program memory. With this amount of available addressable space, the PIC18C601/801 devices become ideal candidates for more complex applications (e.g. TCP/IP stacks), developed with high level programming languages, such as `C'. In addition, PIC18C601/801 devices also make in-system programming possible with its configurable general purpose RAM ("Boot RAM"), which can be configured as a program memory. When program execution takes place from Boot RAM, the external memory bus can be mapped to port I/O. This feature enables the device to perform virtually any programming algorithm in software which does not conform to standard timing requirements. Also, the PIC18C801 offers a completely "glueless" external memory interface solution with its 8-bit De-Multiplexed Interface mode. Given the number and types of memories available today, finding and interfacing memory to the PIC18C601/801 devices potentially becomes a challenging task. This application note describes the PIC18C601/801 external memory interface modes, as well as the methods for interfacing different types of memories with PIC18C601/801. It is expected that the reader will already be familiar with the general PIC18 architecture and instruction set. This application note is divided into the following sections. * External Program Memory Interface Modes provide information on the various memory interface modes available with the PIC18C601/801 microcontrollers. It also discusses the requirements for configuring the controllers and using Table Read and Table Write operations. * Memory Mapping explains the memory maps and mapping techniques for the PIC18C601/801 devices, using the on-chip programmable chip select signals. * Memory Mapped I/O explains how to use the external memory interface as a mapped I/O port for peripheral devices. * Memory Devices and Interface provides information on selecting and implementing interfaces for various types of memory devices. * Memory Timing Analysis explains the memory timing requirements for PIC18C601/801 devices, and how to assess memory devices for compatability. The goal of this section is to answer one of the most frequently asked questions: "What memory speed should I use with my x MHz CPU?" The PIC18C601/801 devices provide up to two programmable chip select signals, to partition address space into two different memories. It also provides one programmable I/O chip select signal to locate an 8 Kbyte memory mapped I/O region anywhere in the address space, except the lower 8 Kbyte space. 2001 Microchip Technology Inc. DS00778A-page 1 AN778 1.0 EXTERNAL PROGRAM MEMORY INTERFACE MODES PIC18C601/801 controllers can be configured to run in either 8-bit or 16-bit Data mode. The appropriate mode is selected by setting the Bus Width configuration bit (BW) in the Configuration register CONFIG2L. The default configuration for the controllers is 16-bit, but this can be changed to 8-bit with the appropriate device programmer. The 16-bit Data mode is available only in Multiplexed mode, regardless of part selection. Depending on the part chosen, the 8-bit Data mode may be either multi- REGISTER 1-1: plexed or de-multiplexed; the PIC18C601 supports only the Multiplexed mode, while the PIC18C801 provides only the De-Multiplexed mode. If the external address bus is configured as an 8-bit external interface, some of the external control signals used in the 16-bit external interface will be mapped to port I/O functions. However, when the external address bus is configured as 16-bit external interface, all of the external control signals used for the 8-bit external interface will also be used for the 16-bit interface. External components are needed to de-multiplex the address for all interface modes. The exception is the PIC18C801 configured in 8-bit Interface mode (Section 1.3.2). CONFIGURATION REGISTER 2 LOW (CONFIG2L: BYTE ADDRESS 300002h) U-0 R/P-1 U-0 U-0 U-0 U-0 U-0 R/P-1 -- BW -- -- -- -- -- PWRTEN bit 7 bit 0 bit 7 Unimplemented: Read as '0' bit 6 BW: External Bus Data Width bit 1 = 16-bit external bus mode 0 = 8-bit external bus mode bit 5-1 Unimplemented: Read as '0' bit 0 PWRTEN: Power-up Timer Enable bit 1 = PWRT disabled 0 = PWRT enabled Legend: R = Readable bit P = Programmable bit - n = Value when device is unprogrammed DS00778A-page 2 U = Unimplemented bit, read as `0' u = Unchanged from programmed state 2001 Microchip Technology Inc. AN778 1.1 Physical Implementation The External Memory Interface is implemented with up to 26 pins on the PIC18C601, and up to 38 pins on the PIC18C801. These pins are reserved for external address and data bus functions. and are also multiplexed with port pins. The port functions are only enabled when: Tables 1-1 and 1-2 list the typical mappings of external bus functions on I/O pins for the PIC18C601 and PIC18C801, respectively. * Program execution takes place in internal Boot RAM, and * The EBDIS bit in the MEMCON register is set (MEMCON<7> = `1'). TABLE 1-1: TYPICAL PORT FUNCTIONS OF PIC18C601 16-bit mode 8-bit mode RD0/AD0 AD0 AD0 Input/Output or System Bus Address bit 0 or Data bit 0 RD1/AD1 AD1 AD1 Input/Output or System Bus Address bit 1 or Data bit 1 RD2/AD2 AD2 AD2 Input/Output or System Bus Address bit 2 or Data bit 2 RD3/AD3 AD3 AD3 Input/Output or System Bus Address bit 3 or Data bit 3 RD4/AD4 AD4 AD4 Input/Output or System Bus Address bit 4 or Data bit 4 RD5/AD5 AD5 AD5 Input/Output or System Bus Address bit 5 or Data bit 5 RD7/AD6 AD6 AD6 Input/Output or System Bus Address bit 6 or Data bit 6 RD6/AD7 AD7 AD7 Input/Output or System Bus Address bit 7 or Data bit 7 RE0/AD8 AD8 AD8 Input/Output or System Bus Address bit 8 or Data bit 8 RE1/AD9 AD9 AD9 Input/Output or System Bus Address bit 9 or Data bit 9 RE2/AD10 AD10 AD10 Input/Output or System Bus Address bit 10 or Data bit 10 RE3/AD11 AD11 AD11 Input/Output or System Bus Address bit 11 or Data bit 11 RE4/AD12 AD12 AD12 Input/Output or System Bus Address bit 12 or Data bit 12 RE5/AD13 AD13 AD13 Input/Output or System Bus Address bit 13 or Data bit 13 RE6/AD14 AD14 AD14 Input/Output or System Bus Address bit 14 or Data bit 14 RE7/AD15 AD15 AD15 Input/Output or System Bus Address bit 15 or Data bit 15 RG0/ALE ALE ALE Address Latch Enable (ALE) Control pin RG1/OE OE OE Output Enable (OE) Control pin RG2/WRL WRL WRL Write Low (WRL) Control pin RG3/WRH WRH RG3 Input/Output or System Bus Write High (WRH) Control pin RG4/BA0 BA0 BA0 Input/Output or System Bus Byte Address bit 0 LB RF7 Input/Output or System Bus Lower Byte Enable (LB) Control pin Name RF7/LB RF6/UB Function UB RF6 Input/Output or System Bus Upper Byte Enable (UB) Control pin RF3/CSIO CSIO CSIO Input/Output or System Bus Chip Select I/O RF4/AD16 AD16 AD16 Input/Output or System Bus Address bit 16 or Data bit 16 RF5/CS1 CS1 CS1 Input/Output or System Bus Chip Select 1 2001 Microchip Technology Inc. DS00778A-page 3 AN778 TABLE 1-2: TYPICAL PORT FUNCTIONS OF PIC18C801 16-bit mode 8-bit mode RD0/AD0 AD0 A0 Input/Output or System Bus Address bit 0 or Data bit 0 RD1/AD1 AD1 A1 Input/Output or System Bus Address bit 1 or Data bit 1 RD2/AD2 AD2 A2 Input/Output or System Bus Address bit 2 or Data bit 2 RD3/AD3 AD3 A3 Input/Output or System Bus Address bit 3 or Data bit 3 RD4/AD4 AD4 A4 Input/Output or System Bus Address bit 4 or Data bit 4 RD5/AD5 AD5 A5 Input/Output or System Bus Address bit 5 or Data bit 5 RD7/AD6 AD6 A6 Input/Output or System Bus Address bit 6 or Data bit 6 RD6/AD7 AD7 A7 Input/Output or System Bus Address bit 7 or Data bit 7 RE0/AD8 AD8 A8 Input/Output or System Bus Address bit 8 or Data bit 8 Name Function RE1/AD9 AD9 A9 Input/Output or System Bus Address bit 9 or Data bit 9 RE2/AD10 AD10 A10 Input/Output or System Bus Address bit 10 or Data bit 10 RE3/AD11 AD11 A11 Input/Output or System Bus Address bit 11 or Data bit 11 RE4/AD12 AD12 A12 Input/Output or System Bus Address bit 12 or Data bit 12 RE5/AD13 AD13 A13 Input/Output or System Bus Address bit 13 or Data bit 13 RE6/AD14 AD14 A14 Input/Output or System Bus Address bit 14 or Data bit 14 RE7/AD15 AD15 A15 Input/Output or System Bus Address bit 15 or Data bit 15 RH0/A16 A16 A16 Input/Output or System Bus Address bit 16 RH1/A17 A17 A17 Input/Output or System Bus Address bit 17 RH2/A18 A18 A18 Input/Output or System Bus Address bit 18 RH3/A19 A19 A19 Input/Output or System Bus Address bit 19 RG0/ALE ALE ALE Address Latch Enable (ALE) Control pin Output Enable (OE) Control pin OE OE RG2/WRL WRL WRL Write Low (WRL) Control pin RG3/WRH WRH RG3 Input/Output or System Bus Write High (WRH) Control pin RG4/BA0 BA0 BA0 Input/Output or System Bus Byte Address bit 0 RF7/LB LB RF7 Input/Output or System bus Lower Byte Enable (LB) Control pin RF6/UB UB RF6 Input/Output or System Bus Upper Byte Enable (UB) Control pin RF3/CSIO CSIO CSIO Input/Output or System Bus Chip Select I/O RF4/CS2 CS2 CS2 Input/Output or System Bus Chip Select 2 RF5/CS1 CS1 CS1 Input/Output or system bus Chip Select 1 RJ0/D0 RJ0 D0 Input/Output or System Bus Data bit 0 RJ1/D1 RJ1 D1 Input/Output or System Bus Data bit 1 RJ2/D2 RJ2 D2 Input/Output or System Bus Data bit 2 RJ3/D3 RJ3 D3 Input/Output or System Bus Data bit 3 RJ4/D4 RJ4 D4 Input/Output or System Bus Data bit 4 RJ5/D5 RJ5 D5 Input/Output or System Bus Data bit 5 RJ6/D6 RJ6 D6 Input/Output or System Bus Data bit 6 RJ7/D7 RJ7 D7 Input/Output or System Bus Data bit 7 RG1/OE DS00778A-page 4 2001 Microchip Technology Inc. AN778 1.2 16-bit External Interfaces The 16-bit External mode interface can be configured by setting BW bit in Configuration register, CONFIG2L. Pins AD15:AD0 carry multiplexed address and data information, while pins A19:A16 carry address information only. The BA0 signal indicates an even or odd address. Since all memory accesses by the controller in 16-bit mode are word-aligned, BA0 is not required and should be left unconnected, even though it is still active. For 16-bit instruction fetch mode, the OE output enable signal will enable both bytes of program memory at once to get a 16-bit word. PIC18C601/801 controllers divide their instruction cycle into four quarters, Q1 through Q4. During Q1, ALE is enabled while address information (A15:A0) is TABLE 1-3: placed on pins AD15:AD0. At the same time, the upper address information (Ax:A16) is available on the upper address bus. On the negative edge of ALE, the address is latched in the external latch. At the beginning of Q3, the OE output enable (active low) signal is generated. At the end of Q4, OE goes high and data (16-bit word) is read from memory at the low-to-high transition edge of OE. The 16-bit mode is divided into three sub-categories, depending on how external memory is organized: * 16-bit memory with two individual 8-bit memory chips (Byte Write mode) * 16-bit memory with Byte Select mode * True 16-bit memory (16-bit Word Write mode) The control signals used for the 16-bit modes are listed in Table 1-3. 18C601/801 16-BIT MODE CONTROL SIGNALS Name 18C601 16-bit mode 18C801 16-bit mode RG0/ALE ALE ALE Address Latch Enable (ALE) Control pin RG1/OE OE OE Output Enable (OE) Control pin Function RG2/WRL WRL WRL Write Low (WRL) Control pin RG3/WRH WRH WRH Write High (WRH) Control pin RG4/BA0 BA0 BA0 Byte Address bit 0 RF3/CSIO CSIO CSIO Chip Select I/O (see Section 3.3) RF4/CS2 N/A CS2 Chip Select 2 (see Section 3.2) RF5/CS1 CS1 CS1 Chip Select 1 (see Section 3.1) RF6/UB UB UB Upper Byte Enable (UB) Control pin RF7/LB LB LB Lower Byte Enable (LB) Control pin I/O I/O I/O I/O as BYTE/WORD Control pin for JEDEC FLASH (with Byte Select mode) 2001 Microchip Technology Inc. DS00778A-page 5 AN778 1.2.1 TABLE READ AND WRITE OPERATIONS IN 16-BIT MODE In addition to the program memory space already covered, PIC18C601/801 devices also have a data memory space. These memory spaces differ in their organization: program memory is 16-bits wide, while data memory is 8-bits wide. To move information between these differently configured spaces, the Table Read (TBLRD) and Table Write (TBLWT) instructions have been provided. Table Read operations retrieve data from program memory and place it into the data memory space. Table Write operations, on the other hand, store data from the data memory space into program memory. Table operations work with byte entities, moving data through an 8-bit register, TABLAT. A table block containing data is not required to be word aligned, so a table block can start or end at any byte address. REGISTER 1-2: All of the 16-bit modes require special handling of Table Write operations. The appropriate bits in the MEMCON register (WM, or MEMCON<1:0>) must be set prior to any Table Write operation. At power-on, the default content of MEMCON sets the following system parameters: * System bus is enabled * Program RAM is configured as GPR memory from 400h to 5FFh * A 3-wait state cycle count for Table Reads and Writes is selected * Table Write operations are set for Byte Write mode Register 1-2 gives the details of the MEMCON configuration bits. Note: The WM<1:0> bits have no effect when the device is configured for 8-bit execution. MEMCON REGISTER R/W-0 R/W-0 R/W-0 R/W-0 U-0 U-0 R/W-0 R/W-0 EBDIS PGRM WAIT1 WAIT0 -- -- WM1 WM0 bit7 bit0 bit 7 EBDIS: External Bus Disable bit 1 = External system bus disabled, all external bus drivers are mapped as I/O ports 0 = External system bus enabled and I/O ports are disabled bit 6 PGRM: Program RAM Enable bit 1 = 512 bytes of internal RAM enabled as internal program memory from location 1FFE00h to 1FFFFFh, external program memory at these locations is unused. Internal GPR memory from 400h to 5FFh is disabled and returns 00h. 0 = Internal RAM enabled as internal GPR memory from 400h to 5FFh. Program memory from location 1FFE00h to 1FFFFFh is configured as external program memory. bit 5-4 WAIT<1:0>: Table Reads and Writes Bus Cycle Wait Count bits 11 = Table reads and writes will wait 0 TCY 10 = Table reads and writes will wait 1 TCY 01 = Table reads and writes will wait 2 TCY 00 = Table reads and writes will wait 3 TCY bit 3-2 Unimplemented: Read as '0' bit 1-0 WM<1:0>: TBLWT Operation with 16-bit Bus bits 1X = Word Write mode: TABLAT<0> and TABLAT<1> word output, WRH active when TABLAT<1> written 01 = Byte Select mode: TABLAT data copied on both Most Significant Byte and Least Significant Byte, WRH and (UB or LB) will activate 00 = Byte Write mode: TABLAT data copied on both Most Significant Byte and Least Significant Byte, WRH or WRL will activate Legend: DS00778A-page 6 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared x = Bit is unknown 2001 Microchip Technology Inc. AN778 1.2.1.1 TABLAT and TBLPTR Registers 1.2.1.2 Two control registers are used in conjunction with the TBLRD and TBLWT instructions. They are: * TABLAT register * TBLPTR registers The Table Latch (TABLAT) is an 8-bit register mapped into the SFR space. The Table Latch is used to hold 8-bit data during data transfers between program memory and data memory. The Table Pointer (TBLPTR) addresses a byte within the program memory. The TBLPTR is comprised of three special function registers: * Table Pointer Upper byte (TBLPTRU) * Table Pointer High byte (TBLPTRH) * Table Pointer Low byte (TBLPTRL) These three registers join to form a 21-bit wide pointer, which allows the device to address up to 2 Mbytes of program memory space. TBLPTR is used by the TBLRD and TBLWT instructions. During Table Read and Table Write operations, the Least Significant bit of TBLPTR is copied to BA0. The remainder of TBLPTR is copied to pins AX:A0 of the external address bus, with the upper limit being determined by the microcontroller and mode being used. As an example, when the PIC18C801 is being used, the value of TBLPTR<0> appears on BA0, while the values of TBLPTR<20:1> appear on pins A19:A0. EXAMPLE 1-1: movlw movwf movlw movwf movlw movwf movlw movwf tblwt*+ movlw movwf tblwt* movf Table Read The TBLRD instruction is used to retrieve data from external program memory and place it into data memory. TBLPTR points to a byte address in external program memory space. Executing TBLRD, places the byte into TABLAT. In addition, TBLPTR can be modified automatically for the next Table Read operation. Table Reads from external program memory are logically performed one byte at a time. If the external interface is 8-bit, the bus interface circuitry in TABLAT will load the external value into TABLAT. If the external interface is 16-bit, interface circuitry in TABLAT will select either the high, or the low byte of the data from the 16-bit bus, based on the Least Significant bit of the address. That is, when LSb is 0, the lower byte (D<7:0>) is selected; when LSb is 1, the upper byte (D<15:8>) is selected. 1.2.1.3 Table Write The TBLWT instruction stores data from the data memory space into external program memory. PIC18C601/801 devices perform Table Writes, one byte at a time. Table Writes to external memory are two-cycle instructions, unless wait states are enabled. If the external interface is 8-bit, the bus interface circuitry in TABLAT will copy its value to the external data bus. If the external interface is 16-bit, interface Table Writes depend on the type of external device that is connected and the WM<1:0> bits in the MEMCON register. The code in Example 1-1 describes the use of the Table Write operation for the 16-bit external interface. USING THE TBLWT INSTRUCTION WITH THE 16-BIT INTERFACE UPPER TBLPTRU HIGH TBLPTRH LOW TBLPTRL LOW TABLAT (SampleTable) (SampleTable) (SampleTable) (DataWord) HIGH (DataWord) TABLAT Count,W 2001 Microchip Technology Inc. ;Initialize Table Pointer ;with the starting address ;of the Table ; ; ; ;Load table latch with low byte ;of value to write ;Write to Program memory and increment Table Pointer ;Load W register with high byte of value to write ;Transfer high byte of value to table latch ;Write to next location/Word ;Next Instruction for logic DS00778A-page 7 AN778 1.2.2 EXTERNAL TABLE WRITE IN 16-BIT BYTE WRITE MODE TBLWT instruction cycle, the TABLAT data is presented on the upper and lower bytes of the AD15:AD0 bus. The appropriate WRH or WRL control line is strobed on the LSb of the TBLPTR. This mode is used for two separate 8-bit memories connected for 16-bit operation. This generally includes basic EPROM and FLASH devices. It allows Table Writes to byte-wide external memories. During a FIGURE 1-1: Figure 1-1 shows a typical implementation of the Byte Write mode. 16-BIT BYTE WRITE MODE Byte-Wide Memory D<15:8> A<16:0>(1)/ A<19:0>(2) A/16(1)/A<19:16>(2) (LSB) A<16:0>(1)/ A<19:0>(2) (MSB) A<16:0>(1)/ A<19:0>(2) D<7:0> D<7:0> LATCH AD<15:8> D<7:0> PIC18C601/801 CE CE LATCH OE AD<7:0> ALE WR (4) OE CS CS1 or CS2(3) CS OE OE OE WRL WRL(4) WRH WRH(4) DS00778A-page 8 WR(4) Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. 4: This signal is not used for ROM and EPROM external memory. LEGEND Address Lines Data Lines Control Lines 2001 Microchip Technology Inc. AN778 1.2.3 EXTERNAL TABLE WRITE IN 16-BIT BYTE SELECT MODE Note: This mode allows Table Write operations to word-wide external memories with byte selection capability. This generally includes both word-wide FLASH and SRAM devices. During a TBLWT cycle, the TABLAT data is presented on the upper and lower byte of the AD15:AD0 bus. The WRH signal is strobed for each write cycle; the WRL pin is not used. The BA0 or UB/LB signals are used to select the byte to be written, based on the LSb of the TBLPTR register. FLASH and SRAM devices use different control signal combinations to implement Byte Select mode. JEDEC standard FLASH memories require that a controller I/O port pin be connected to the memory's BYTE/WORD pin to provide the select signal. They also use the BA0 signal from the controller as a byte address (Figure 1-2). JEDEC standard static RAM memories, on the other hand, use the UB or LB signals to select the byte (Figure 1-3). FIGURE 1-2: To program a 16-bit FLASH memory with byte select capability, user firmware must dynamically change FLASH memory access mode from Word to Byte mode. This can be achieved by connecting one I/O line to a FLASH Memory mode pin and making sure that the FLASH device is setup in 16-bit mode on power-up. Since instruction fetches are done in 16-bit mode only, care must be taken that FLASH mode is changed only when execution is taking place from Boot RAM. For additional information, refer to the PIC18C601/801 Device Data Sheet (DS39541). 16-BIT BYTE SELECT MODE (WORD-WIDE FLASH MEMORY) JEDEC Word FLASH Memory(5) A17(1)/A<20:17>(2) A16(1)/A<19:16>(2) A<15:8> A<15:0> A<16:1> LATCH D<15:0> AD<15:8> A0 D<15:0> WORD/BYTE PIC18C601/801 CE LATCH AD<7:0> OE WR(4) A<7:0> ALE A0 BA0 IO I/O CS CS1 or CS2(3) OE OE WRH WRH(4) Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. 4: This signal is not used for ROM and EPROM external memory. 5: This family of FLASH memory ignores A0 in Word mode. 2001 Microchip Technology Inc. LEGEND Address Lines Data Lines Control Lines DS00778A-page 9 AN778 FIGURE 1-3: 16-BIT BYTE SELECT MODE (WORD-WIDE SRAM) JEDEC Word SRAM A16(1)/A<19:16>(2) A16(1)/A<19:16>(2) A<15:0> A<15:0> LATCH A<15:8> AD<15:8> D<15:0> D<15:0> PIC18C601/801 UB LB LATCH A<7:0> AD<7:0> CE OE WR ALE UB UB LB LB CS CS1 or CS2(3) OE OE WRH WRH DS00778A-page 10 Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. LEGEND Address Lines Data Lines Control Lines 2001 Microchip Technology Inc. AN778 1.2.4 EXTERNAL TABLE WRITE IN 16-BIT WORD WRITE MODE This mode is used for word-wide memories, which includes some of the EPROM and FLASH type memories. This mode allows opcode fetches and Table Reads from all forms of 16-bit memory, and Table Writes to any type of word-wide external memories. This method makes a distinction between TBLWT cycles to even or odd addresses. During a TBLWT cycle to an even address (TBLPTR<0> = `0'), the TABLAT data is transferred to a holding latch and the external address data bus is tri-stated for the data portion of the bus cycle. No write signals are activated. FIGURE 1-4: During a TBLWT cycle to an odd address (TBLPTR<0> = `1'), the TABLAT data is presented on the upper byte of the AD15:AD0 bus. The contents of the holding latch are presented on the lower byte of the AD15:AD0 bus. The WRH signal is strobed for each write cycle; the WRL pin is unused. The signal on the BA0 pin indicates the LSb of TBLPTR, but it is left unconnected. Instead, the UB and LB signals are active to select both bytes. The obvious limitation to this method is that the Table Write must be done in pairs on a specific word boundary to correctly write a word location. Figure 1-4 shows a typical implementation of this mode. 16-BIT WORD WRITE MODE JEDEC Word FLASH Memory A16(1)/ A<19:16>(2) A16(1)/A<19:16>(2) A<15:8> A<15:0> LATCH A<15:0> D<15:0> AD<15:8> D<15:0> CE PIC18C601/801 OE WR(4) LATCH A<7:0> AD<7:0> ALE CS CS1 or CS2(3) OE OE WRH WRH(4) Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. 4: This signal is not used for ROM and EPROM external memory. 2001 Microchip Technology Inc. LEGEND Address Lines Data Lines Control Lines DS00778A-page 11 AN778 1.3 8-bit External Interfaces 1.3.1 address pins A16:A0 are connected to memory address pins A17:A1. The output enable (OE) signal will enable the first byte of program memory for a portion of the cycle, the second byte will be read to from the 16-bit instruction word when BA0 changes. 8-BIT MULTIPLEXED EXTERNAL INTERFACE This interface is only available on the PIC18C601. It requires the use of either a lower processor operating frequency as compared to 16-bit modes, or the use of a faster memory device. When the 8-bit interface is selected, the WRH, UB and LB pins are not used; they revert to I/O port functions. The WRL signal is active on every external write. The external address is 18-bits wide, which allows for addressing of up to 256 Kbytes. External Table Reads and Table Write are performed one byte at a time. In this mode, the low order address and data bytes are multiplexed, and require a single latch to de-multiplex the address and data busses. Instructions are fetched as two 8-bit bytes within one instruction cycle. Pin BA0 from the controller must be connected to address pin A0 of the memory device(s); because of this, controller FIGURE 1-5: Figure 1-5 shows a typical implementation of this mode. The control signals are described in Table 1-4. 8-BIT MULTIPLEXED MODE FOR PIC18C601 A16 A17 A<15:8> A<16:9> AD<15:8> A<7:0> A<8:1> LATCH AD<7:0> A0 PIC18C601 D<7:0> D7:D0 BA0 CE OE ALE CS1 CS1 OE OE WRL WRL(1) Note 1: TABLE 1-4: This signal is not used for ROM and EPROM external memory. LEGEND Address Lines Data Lines Control Lines 8-BIT MULTIPLEXED MODE CONTROL SIGNALS Name 8-bit Mux mode RG0/ALE ALE Address Latch Enable (ALE) Control pin RG1/OE OE Output Enable (OE) Control pin RG2/WRL WRL Write Low (WRL) Control pin RG4/BA0 BA0 Byte Address bit 0 RF3/CSIO CSIO Chip Select I/O (see Section 3.3) RF5/CS1 CS1 Chip Select 1 (see Section 3.1) DS00778A-page 12 WR(1) Function 2001 Microchip Technology Inc. AN778 1.3.2 8-BIT WITH DE-MULTIPLEXED EXTERNAL INTERFACE This interface is only available on the PIC18C801. It requires the use of either a lower processor operating frequency as compared to 16-bit modes, or the use of a faster memory device. The address and data busses are separate and do not require any external latches for de-multiplexing. The instructions are fetched as two 8-bit bytes on a dedicated data bus (PORTJ); the address is presented for the entire duration of the fetch cycle on a separate address bus. The two bytes are fetched during one instruction cycle. Pin BA0 from the controller must be connected to address pin A0 of the memory device(s); because of this, controller address pins A19:A0 are connected to memory address pins A20:A1. The output enable (OE) signal will enable the first byte of program memory for a portion of the cycle; the second byte will be read to from the 16-bit instruction word when BA0 changes. The external address is 21-bits wide, which allows for addressing of up to 2 Mbytes. External Table Reads and Table Writes are performed one byte at a time. When the 8-bit de-multiplexed interface is selected, the WRH, UB and LB pins are not used; they revert to I/O port functions. The WRL signal is active on every external write. The control signals for this interface are described in Table 1-5. FIGURE 1-6: 8-BIT DE-MULTIPLEXED MODE FOR PIC18C801 A<19:0> A<19:0> A<20:1> A0 BA0 D7:D0 D<7:0> D<7:0> PIC18C801 CE OE WR(1) CS CS1 or CS2(2) OE OE WRL WRL(1) Note 1: This signal is not used for ROM and EPROM external memory. 2: CS2 is available only on the PIC18C801. TABLE 1-5: LEGEND Address Lines Data Lines Control Lines 8-BIT DE-MULTIPLEXED MODE CONTROL SIGNALS Name 8-bit De-Mux Mode RG0/ALE ALE Address Latch Enable (ALE) Control pin RG1/OE OE Output Enable (OE) Control pin RG2/WRL WRL Write Low (WRL) Control pin RG4/BA0 BA0 Byte Address bit 0 RF3/CSIO CSIO Chip Select I/O (see Section 3.3) RF4/CS2 CS2 Chip Select 2 (see Section 3.2) RF5/CS1 CS1 Chip Select 1 (see Section 3.1) 2001 Microchip Technology Inc. Function DS00778A-page 13 AN778 2.0 MEMORY MAPPED I/O 2.1 Discrete Digital Logic In general, latches are required for output ports, while tri-state buffers are used for input ports. In general, ROMless microcontrollers have less dedicated I/O ports available than their ROM equipped counterparts. To get around this limitation, additional I/O channels are made available through memory mapped communications with peripheral devices. Normally, this is achieved in one of two ways: Figure 2-1 demonstrates the requirements for a typical output port. Normally, latches have one active high control signal, with data being latched at the signal's high-to-low transition. The controller data bus (D<7:0>) is connected to the data input bus of the latch. The CSIO and appropriate WR control lines are NORed to produce the latch control signal. * Using discrete digital logic * Using programmable peripherals Figure 2-2 demonstrates the requirements for a digital input interface. Tri-state buffers usually have one active low control signal; when it is active, input data is transferred to the buffer output. The controller data bus (D<7:0>) is connected to the output bus of the buffer. The CSIO and OE lines are ORed to produce the buffer control signal. FIGURE 2-1: OUTPUT INTERFACE USING DISCRETE DIGITAL LOGIC PIC18C601/801 Figure -7 AD<7:0>(1) D<7:0>(2) LATCH D<7:0> Digital Output CSIO WRH WRL Note 1: Configuration for PIC18C601 and PIC18C801 in 16-bit mode. 2: Configuration for PIC18C801 in 8-bit mode.. FIGURE 2-2: INPUT INTERFACE USING DISCRETE DIGITAL LOGIC BUFFER Digital Input NOR Gate Input MODE 8-bit WRL 16-bit, Byte Write WRL 16-bit, Word Write WRH 16-bit, Byte Select WRH D<7:0> PIC18C601/801 AD<7:0>(1) D<7:0>(1) CSIO G OE Note 1: Configuration for PIC18C601 and PIC18C801 in 16-bit mode. 2: Configuration for PIC18C801 in 8-bit mode.. DS00778A-page 14 2001 Microchip Technology Inc. AN778 2.2 Programmable Peripherals The peripheral device's data bus (D7:D0) is connected to the controller's data bus. Peripheral address pins A0 and A1 (in some cases, only A0) are connected to A0 and A1 of the controller. For 8-bit mode, address pins A0 and A1 of the peripheral device (in some case only A0) can be connected with BA0 and A0 of the controller. Some commonly used peripherals, such as the Intel(R) compatible 8255 (programmable peripheral interface) and the 8279 (programmable keyboard/display interface), have 8-bit interfaces. These devices can be connected to ROMless microcontrollers for memory mapped I/O operation, using CSIO as a control line. The RD control pin of the peripheral is connected to the OE pin of the controller. The WR pin of the peripheral is connected to either the WRL or WRH pin of the controller, depending on the memory interface mode. Figures 2-3 through 2-5 demonstrate methods for interfacing programmable peripheral devices with ROMless microcontrollers. Some peripherals (such as the 8255 and 8279) have one or two address lines to select internal registers. As these are 8-bit devices, special care is required for the 16-bit modes. The addressing scheme is selected in such a way that it is common for all modes. The base address will be an even address specified by the CSELIO register. (See Section 3.3 for details on specifying the location of the 8 Kbyte region for I/O). FIGURE 2-3: The internal registers of the peripheral device can be accessed by Table Read and Table Write instructions. Addresses for the registers start with the base address specified by the CSELIO register, incrementing with an offset of 02h in 16-bit mode or 01h in 8-bit mode. (See the Address/Register tables in Figures 2-3 through 2-5 for details.) For 16-bit Table Write operations, the upper byte will be dummy data. 16-BIT MEMORY MAPPED I/O FOR THE PIC18C601/801 - PROGRAMMABLE PERIPHERAL DEVICES MCU Peripheral Address Register CSELIO Base 0 Base + 2 1 2 Base + 4 3 Base + 6 PIC18C601/801 A<1:0> PERIPHERAL A<1:0> D<7:0> AD<7:0> LATCH A<7:0> CE RD WR D<7:0> ALE CSIO OE WRH WRL Interface Mode WR Connected To 16-bit, Byte Write 16-bit, Word Write 16-bit, Byte Select 2001 Microchip Technology Inc. WRL WRH WRH LEGEND Address Lines Data Lines Control Lines DS00778A-page 15 AN778 FIGURE 2-4: 8-BIT MEMORY MAPPED I/O FOR THE PIC18C801 - PROGRAMMABLE PERIPHERAL DEVICES MCU Peripheral Address Register CSELIO Base 0 Base + 2 1 Base + 4 2 Base + 6 3 PERIPHERAL A0 A1 BA0 A0 D<7:0> D<7:0> PIC18C801 D<7:0> CE RD WR CSIO OE WRL LEGEND Address Lines Data Lines Control Lines FIGURE 2-5: 8-BIT MEMORY MAPPED I/O FOR THE PIC18C601 - PROGRAMMABLE PERIPHERAL DEVICES MCU Peripheral Address Register CSELIO Base 0 Base + 2 1 2 Base + 4 3 Base + 6 AD<7:0> PERIPHERAL BA0 BA0 A0 LATCH A0 A1 ALE D<7:0> D<7:0> PIC18C601 CE RD WR CSIO OE WRL LEGEND Address Lines Data Lines Control Lines DS00778A-page 16 2001 Microchip Technology Inc. AN778 3.0 MEMORY MAPPING PIC18C601/801 microcontrollers are capable of supporting a wide variety of memories and memory configurations. Users can connect up to two different types of memories in a single system. Different memories can be enabled or disabled using combinations of the chip select signals. While chip select signals are normally generated by externally decoding the address lines, PIC18C601/801 devices provide up to two programmable on-board chip select signals and one I/O chip select signal. This minimizes the amount of additional external circuitry required to interface the external memory and memory mapped I/O devices. The PIC18C601 provides CS1 and CSIO, while the PIC18C801 provides CS1, CS2 and CSIO. When enabled, a chip select signal is asserted whenever the CPU accesses the dedicated range of addresses, specified in the chip select registers, CSEL2 and CSELIO. If both the CSEL2 and CSELIO registers are 00h, all of the chip selects are disabled, and their corresponding pins are configured as I/O. In addition, when program execution takes place from internal Boot RAM, all chip selects are configured in their inactive states. For the PIC18C601, CS1 is always enabled unless the CSIO signal is active. The CSEL2 register in the PIC18C601 is not implemented, and can be used as a general purpose register. The chip selects are unaffected by any device RESETS, except the Power-on Reset. The RESET value of these registers enable all three chip selects with CS1 active (= `0'), CS2 inactive (= `1'), and CSIO inactive (= `1') (with the RESET address = 000000h). Details of the operation of the chip selects are provided in the following sections. Figure 3-1 further illustrates the relationships between the chip selects and the program memory map. 3.1 CS1 The CS1 signal is active low and inactive high. CS1 is enabled by writing a value other than 00h into either the CSEL2 register, or the CSELIO register. If both registers are programmed to 00h, the CS1 signal is not enabled and the RF5/CS1 pin is configured as I/O. The CS1 signal is active for a range of addresses that are specified in the CSEL2 and CSELIO registers. By default, it is active for the entire program memory range from 000000h to 1FDFFh. It will always be active for the lower 8 Kbytes of program memory. CS1 is active for all addresses for which CS2 and CSIO are inactive. Therefore, if CSEL2 is equal to 20h and CSELIO is equal to 80h, the CS1 signal will be active for the addresses that fall between 000000h and 03FFFFh. When the device cycles through a Power-on Reset, the CS1 chip select is the only active chip select. Note: 3.2 Because it is the only active chip select signal on Power-on Reset, CS1 must always be connected to one of the external memory devices . CS2 The CS2 signal is also active low and inactive high. A value of 00h in the Chip Select 2 Register (CSEL2) disables the CS2 signal and configures the RF4/CS2 pin as I/O. The program memory range for CS2 is determined by the value contained in CSEL2. An 8-bit value in this register determines the starting address for the activation of CS2. The 8-bit value is decoded as one of 256 boundaries in the program memory space, each being 8 Kbyte in size. For example, if the value contained in the CSEL2 register is 128 (80h), then the CS2 signal will be asserted whenever the address is greater than, or equal to 8192 x 128, or 1,048,576 (100000h). When the device cycles through a Power-on Reset, CS2 becomes inactive. 2001 Microchip Technology Inc. DS00778A-page 17 AN778 3.3 CSIO The CSIO signal is also active low and inactive high. A value of 00h in the Chip Select 2 Register (CSEL2) disables the CSIO output, and configures the RF3/CSIO pin as I/O. When the device cycles through a Power-on Reset, CSIO becomes inactive. Note: The I/O chip select is active for a fixed 8 Kbyte address range. The location of the I/O chip select is determined by the value contained in the I/O Chip Select register (CSELIO). The eight-bit value is decoded as one of 256 8 Kbyte banks of program memory that, when addressed, will assert the CSIO output. If, for instance, the value contained in the CSIO register is 128 (80h), then the CSIO pin will be asserted for the address range between and including 8192 x 128 to ((8192 x 128) + 8192), or 100000h to 101FFFh. If the 8 Kbyte address block overlaps the address range of the CS2 signal, the CSIO signal will be active and the CS2 signal will be inactive for that 8 Kbyte block of addresses decoded by the CSELIO register. FIGURE 3-1: The RESET state of both CSEL2 and CSELIO registers on Power-on Reset is FFh. This allows the CS1, CS2 and CSIO signals to be enabled. The CS1 signal will be active for all addresses less than 1FE000h, the CSIO signal is active for all addresses greater than, or equal to 1FE000h, and CS2 is inactive, since it shares the same address value as CSIO. This ensures that the chip select signals are not floating if external memory is present, and its chip enable inputs are tied to the chip selects. EXAMPLE CONFIGURATION ADDRESS MAPS FOR CS1, CS2, AND CSIO CSEL2 = FFh (DEFAULT) CSELIO = FFh (DEFAULT) PROGRAM MEMORY CSEL2 = 80h CSELIO = 00h CSEL2 = 20h CSELIO = 80h PROGRAM MEMORY 000000h PROGRAM MEMORY 000000h 000000h 03FFFFh 040000h 0FFFFFh 100000h 0FFFFFh 100000h 101FFFh 102000h 1FFDFFh 1FFE00h 1FFFFFh = CS1 ACTIVE DS00778A-page 18 1FFDFFh 1FFE00h 1FFFFFh = CS2 ACTIVE = CSIO ACTIVE 1FFDFFh 1FFE00h 1FFFFFh = NO CHIP SELECT ACTIVE INTERNAL EXECUTION IF PGRM = 1 2001 Microchip Technology Inc. AN778 REGISTER 3-1: CSEL2 REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 CSL7 CSL6 CSL5 CSL4 CSL3 CSL2 CSL1 CSL0 bit 7 bit 7-0 bit 0 CSL<7:0>: Chip Select 2 Address Decode bits XXh = All eight bits are compared to the Most Significant bits PC<20:13> of the program counter. If PC<20:13> CSL<7:0> register, then the CS2 signal is low. If PC<20:13> < CSL<7:0>, CS2 is high. 00h = CS2 is inactive Legend: REGISTER 3-2: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared CSELIO REGISTER R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 R/W-1 CSIO7 CSIO6 CSIO5 CSIO4 CSIO3 CSIO2 CSIO1 CSIO0 bit7 bit 7 x = Bit is unknown bit0 CSIO<7:0>: Chip Select I/O Address Decode bits XXh = All eight bits are compared to the Most Significant bits PC<20:13> of the program counter. If PC<20:13> = CSIO<7:0>, then the CSIO signal is low. If not, CSIO is high. 00h = CSIO is inactive Legend: R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR '1' = Bit is set '0' = Bit is cleared 2001 Microchip Technology Inc. x = Bit is unknown DS00778A-page 19 AN778 4.0 MEMORY DEVICES AND INTERFACES The PIC18C601/801 ROMless devices are designed to support a variety of memory devices. A variety of control signals are provided to facilitate the interface with many memory chips. 4.1 4.1.1 Memory Devices with x8 Organization x8 ARRANGEMENT In this arrangement, address pins AX:A0 of the controller are connected to address pins AX+1:A1 of the memory device. Pin BA0 is connected to the A0 pin of memory. Controller data pins D7:D0 are connected to memory data lines D7:D0. The controller's OE pin is connected to the OE pin of the memory device, and the controller's WRL pin is connected to the memory's WE pin. For the PIC18C801, all address and data signals are directly available at pin. For the PIC18C601, pins AD7:AD0 are multiplexed; one external latch is required for de-multiplexing the address and data busses. Instructions are fetched as two 8-bit bytes. The output enable (OE) signal will enable one byte of program memory for a portion of cycle, then the LSb of address BA0 will change and the second byte will be read to from the 16-bit instruction word. External Table Reads and Table Writes are performed one byte at a time. Examples of the 8-bit interfaces are provided in Figure 1-5 (Multiplexed mode) and Figure 1-6 (De-Multiplexed mode). Note: 4.1.2 The 8-bit memory interfaces require the use of either faster memory devices, or a lower controller operating frequency (as compared to similar 16-bit interfaces). x16 ARRANGEMENT For this arrangement, two byte-wide memory chips are used, one each for the LSB and MSB. The controller address lines AX:A0 are connected to the AX:A0 address lines of both memories. BA0 is left unconnected. The controller data lines are connected to D7:D0 of one memory device (LSB), and to D15:D8 of the second device (MSB). The controller OE pin is connected with the OE pin of both memories. The controller WRL pin is connected to WE of the LSB memory, while WRH is connected to WE of the MSB memory. External Table Reads are logically performed one byte at a time, although the memory will read a 16-bit word externally. The Least Significant bit of the address internally selects between high and low bytes. For Table Writes, configure the MEMCON register for Byte Write mode (MEMCON<1:0>='00'). During a TBLWT cycle, the TABLAT data is presented on the upper and lower byte of the AD bus. The appropriate WRH or WRL signal is strobed based on the LSb of the TBLPTR. An example of this interface is provided in Figure 1-1. 4.2 Memory Devices with x16 Organization For this arrangement, the controller address pins AX:A0 are connected to the memory address pins AX:A0. BA0 is not used, and left unconnected. The controller data pins D15:D0 are connected to D15:D0 of the memory device. The controller's OE control pin is connected with the OE pin of the memory, and the controller's WRH pin is connected to the memory's WE pin. Instructions are fetched as a single 16-bit word. The output enable (OE) signal will enable word from memory for a portion of the cycle to get the 16-bit instruction word. External Table Reads are logically performed one byte at a time, although the memory will read a 16-bit word externally. The Least Significant bit of the address will internally select between high and low bytes. For Table Write, configure the MEMCON register for Word Write mode (MEMCON<1:0>='1x'). During a TBLWT cycle to an even address (TBLPTR<0> = `0'), the TABLAT data is transferred to a holding latch and the external address data bus is tri-stated for the data portion of the bus cycle. No write signals are activated. During a TBLWT cycle to an odd address (TBLPTR<0> = `1'), the TABLAT data is presented on the upper byte of the AD bus (AD15:AD8). The contents of the holding latch are presented on the lower byte of the AD bus (AD7:AD0). The WRH signal is strobed for each write cycle and the WRL signal is unused. The BA0 signal indicates the LSb of TBLPTR, but it is not used. The UB and LB control signals are active to select both bytes. An example of the 16-bit Word Write interface is shown in Figure 1-4. Instructions are fetched as a 16-bit word. The output enable (OE) signal will enable one byte of both memories for a portion of cycle to form the 16-bit instruction word. DS00778A-page 20 2001 Microchip Technology Inc. AN778 4.3 Memory Devices with x8/x16 Selectable Organization Instructions are fetched as two 8-bit bytes. The output enable (OE) signal will enable one byte of program memory for the first portion of cycle; then the BA0 signal changes, and the second byte is read to form the 16-bit instruction word. External Table Reads and Table Writes are performed one byte at a time. The memory devices covered in this section are capable of supporting both x8 and x16 organization. The method used for interfacing a device depends on the organization used. Additionally, the addressing modes discussed here differ on how the controller address lines are used to fetch byte or word entities. To distinguish these, the schemes in this section will be referred to as "Basic Byte" and "Basic Word". 4.3.1 4.3.1.2 For this arrangement, the controller's AX:A0 address pins are connected to address pins AX+1:A1 of memory. Controller pin BA0 and memory pin A0 are left unconnected. The controller's D15:D0 data pins are connected to the memory's D15:D0 data pins. The controller and memory OE pins are connected, while the controller's WRH pin is connected to the WE pin of the memory. The connections for this mode are shown in Figure 4-3. "BASIC BYTE" ADDRESSING SCHEMES In this scheme, all available memory address lines are used to directly address byte-size data entities. In general, TSOP56 package JEDEC FLASH devices fall into the "Basic Byte" category. 4.3.1.1 For Byte Select mode, the controller's BA0 pin must be connected to A0 of the memory. The WORD/BYTE pin of the memory is connected to an I/O pin on the controller to enable dynamic Word/Byte mode switching. Dynamic switching of FLASH devices is not possible if a program is executing from the same FLASH at the same time. See Section 1.2.3 for more information. Byte (8-bit) Mode The arrangement is similar to the 8-bit modes illustrated in Figures 1-5 and 1-6. Address pins AX:A0 for the controller are connected to address pins AX+1:A1 of memory. The controller's BA0 pin is connected to A0 of the memory device. For the PIC18C801, data pins D7:D0 are connected directly to the data pins of the memory, providing a "glueless" interface (Figure 4-2). For the PIC18C601, the low order address and data signals are multiplexed; controller pins AD7:AD0 are directly connected to the memory to provide data, while an external latch de-multiplexes address pins A7:A0 (Figure 4-1). The controller and memory OE pins are connected, while the controller WRL pin is connected to the memory WR pin. FIGURE 4-1: Word (16-bit) Mode Instructions are fetched as 16-bit words. The output enable (OE) signal will enable word from memory for a portion of cycle to fetch the 16-bit instruction word. External Table Reads and Writes are logically performed one byte at a time, although the memory will read a 16-bit word externally. The Least Significant bit of the address will internally select between high and low bytes. Table Writes can be performed in either Word Write or Byte Select mode. (Refer to Sections 1.2.3 and 1.2.4 for more details.) 8-BIT "BASIC BYTE" ADDRESSING SCHEME FOR THE PIC18C601 A<16:0> A16 A<15:8> AD<15:8> AD<7:0> LATCH A<7:0> A<17:1> D<7:0> A0 WORD/ BYTE D<7:0> PIC18C601 ALE LEGEND Address Lines Data Lines Control Lines CE OE WR BA0 CS1 OE WRL 2001 Microchip Technology Inc. DS00778A-page 21 AN778 FIGURE 4-2: 8-BIT "BASIC BYTE" ADDRESSING SCHEME FOR THE PIC18C801 A<19:0> A<20:1> A<19:16> A<15:8> AD<15:8> D<7:0> A<7:0> AD<7:0> WORD/ BYTE A0 D<7:0> D<7:0> CE OE WR PIC18C801 BA0 CS1 or CS2(1) OE WRL LEGEND Address Lines Data Lines Control Lines Note 1: CS2 is available only on the PIC18C801. FIGURE 4-3: 16-BIT "BASIC BYTE" ADDRESSING SCHEME FOR THE PIC18C601/801 A16(1)/ A<19:16>(2) A16(1)/A<19:16>(2) A<16:0>(1)/ A<19:0>(2) A<17:1>(1)/ A<20:1>(2) VDD D<15:8> D<7:0> AD<15:8> LATCH A<15:8> WORD/ BYTE D<15:8> CE PIC18C601/801 OE AD<7:0> LATCH WR A<7:0> ALE D<7:0> CS1 or CS2(3) OE WRH DS00778A-page 22 Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. LEGEND Address Lines Data Lines Control Lines 2001 Microchip Technology Inc. AN778 4.3.2 "BASIC WORD" ADDRESSING SCHEMES 4.3.2.2 In this scheme, all available memory address lines are used to address word (16-bit) data entities. Functionally, one pin (e.g. DQ15) is used as the LSb address input, and acts as a multi-function pin, depending on the operation mode (Byte or Word). In general, TSOP48 package FLASH devices fall into the "Basic Word" category. 4.3.2.1 Byte (8-bit) Mode In this arrangement, controller address pins AX:A0 are connected to memory address lines AX:A0. Controller data pins D<7:0> are connected to memory data pins D7:D0. BA0 is connected to a memory multi-function pin (e.g., DQ15). The controller and memory OE pins are connected, while the controller WRL pin is connected to the memory's WE pin. For the PIC18C601, pins AD7:AD0 are multiplexed, so one external latch is required for de-multiplexing the address and data busses (Figure 4-4). For the PIC18C801, data is directly available at pin (Figure 4-5). Instructions are fetched as two 8-bit bytes. The output enable (OE) signal will enable one byte of program memory for a portion of cycle; then the BA0 signal will change state for the LSb of address, and the second byte will be read to from the 16-bit instruction word. External Table Reads and Table Writes are performed one byte at a time. FIGURE 4-4: Word (16-bit) Mode For this arrangement, controller address pins AX:A0 are connected to memory address pins AX:0. BA0 is left unconnected. The controller data pins D15:D0 pins are connected to memory data pins D15:D0. The controller and memory OE pins are connected, while controller pin WRH is connected to the memory's WE pin. The connections for this mode are shown in Figure 4-6. Instructions are fetched as one 16-bit word. The output enable (OE) signal will enable word from memory for a portion of the cycle to get the 16-bit instruction word. External Table Reads and Writes are logically performed one byte at a time, although the memory will read a 16-bit word externally. The Least Significant bit of the address will internally select between high and low bytes. For Byte Select mode, the controller's BA0 pin must be connected to pin D15/A1 of the memory. The WORD/BYTE pin of the memory is connected to an I/O pin on the controller to enable dynamic Word/Byte mode switching. Dynamic switching of FLASH devices is not possible if a program is executing from the same FLASH at the same time. See Section 1.2.3 for more information. Table Writes can be performed in either Word Write or Byte Select mode. (Refer to Sections 1.2.3 and 1.2.4 for more details.) 8-BIT "BASIC WORD" ADDRESSING SCHEME FOR THE PIC18C601 A<16:0> A16 A<16:0> D<7:0> A<15:8> AD<15:8> D15/A1 CE AD<7:0> PIC18C601 LATCH WORD/ BYTE A<7:0> OE WR D<7:0> ALE BA0 CS1 OE WRL LEGEND Address Lines Data Lines Control Lines 2001 Microchip Technology Inc. DS00778A-page 23 AN778 FIGURE 4-5: 8-BIT "BASIC WORD" ADDRESSING SCHEME FOR THE PIC18C801 A<19:0> A<19:16> A<19:0> A<15:8> D<7:0> AD<15:8> AD<7:0> A<7:0> D15/A1 D<7:0> OE WORD/ BYTE WR D<7:0> PIC18C801 BA0 OE WRL LEGEND Address Lines Data Lines Control Lines FIGURE 4-6: 16-BIT "BASIC WORD" ADDRESSING SCHEME FOR THE PIC18C601/801 A16(1)/ A<19:16>(2) A16/A<19:16>(2) A<16:0>(1)/ A<19:0>(2) A<16:0>(1)/ A<19:0>(2) VDD D<14:8> D<7:0> AD<15:8> LATCH A<15:8> D15/A1 WORD/ BYTE D<14:8> PIC18C601/801 AD<7:0> D15 LATCH ALE CE OE WR A<7:0> D<7:0> CS1 or CS2(3) OE WRH Note 1: PIC18C601 devices only. 2: PIC18C801 devices only. 3: CS2 is available only on the PIC18C801. DS00778A-page 24 LEGEND Address Lines Data Lines Control Lines 2001 Microchip Technology Inc. AN778 5.0 MEMORY TIMING CONSIDERATIONS In mathematical terms, this means: tOE < TOE, or tOE < 0.5TCY-25 ns Instruction fetching depends on the processor speed, so memory used must provide data output at that speed. This requires consideration on selection of memory for required access time. The memory access time is dependent on main oscillator frequency and External Interface mode. The 8-bit mode requires either a faster memory or a lower processor operating frequency than is available in 16-bit mode. Most of the program memory timing characteristics are defined relative to the instruction cycle period (TCY). This period equals four times the input oscillator time-base period (TOSC), or one-fourth of the oscillator frequency (FOSC): TCY = 4/FOSC = 4 * TOSC For a data read operation, it is apparent that address access time for the memory (address to output delay, or tACC) must be less than the controller's TACC (address valid to data valid delay). However, it is also necessary to consider the propagation delay of the external latch, or tPROP. Depending on the choice of TTL technology, tPROP varies from 5 ns to 40 ns. For 16-bit modes, the memory access time may be expressed by the relationship: tACC < TACC - tPROP For 8-bit mode, the BA0 signal toggles within the OE period to fetch word instruction. Therefore, memory devices for 8-bit mode systems should supply data in half the time of 16-bit mode systems. The memory access time for 8-bit mode is expressed by the relationship: tACC < (TACC - tPROP) / 2 Another consideration is the memory device's tOE, or OE to output delay. This must be less than the microcontroller's TOE (time from OE falling edge to data valid) of 0.5TCY-25 ns. The OE pulse width is fixed, so if tOE is longer than TOE, it will not meet the requirement for the minimum data setup time of 20 ns. TABLE 5-1: * After establishing that the controller can successfully access the memory, it's still necessary to compare the memory device's data hold (tOH) and float (tDF) specifications with the controller's ToeH2adD specification (time from OE low-to-high transition to AD driven). Although access time is the main criteria for determining device compatibility, the data float time (also occasionally referred to as the un-access time) can't be ignored. If the memory device output is unable to go to float in this interval, a bus contention situation will result, in which the next cycle address driven by the CPU will collide with the remnants of the previous cycle memory output. So mathematically, tDF < ToeH2adD Finally, the external latch used for de-multiplexing the address/data busses must satisfy some of its own timing requirements: * It must be able to operate within the ALE pulse width interval of 0.25TCY; * The address must set in the latch within the latch address setup time. This is defined as the interval from address out to the ALE trailing edge, or 0.25TCY-10 ns; * The address should latch when the ALE signal goes low; and * Any additional address hold time following the ALE trailing edge should be less than the time from the trailing edge to the address out invalid time of 5 ns. Table 5-1 lists approximate memory timing requirements for some typical oscillator frequencies. Normally, if access time requirements are met, all other requirements will match. Detailed timing diagrams and requirements follow on the next two pages. Figure 5-1 and Table 5-2 provide information on 16-bit timing operations, while Figure 5-2 and Table 5-3 provide the same information for 8-bit operations. SELECTED MEMORY TIMING REQUIREMENTS AT VARIOUS OSCILLATOR FREQUENCIES Oscillator Frequency tACC* (16-bit mode) tACC* (8-bit mode) tOE tDF TadV2aIL Address Setup Time <240 ns 4 MHz <715 ns <360 ns <475 ns <120 ns 10 MHz <265 ns <130 ns <175 ns <45 ns <90 ns 16 MHz <150 ns <75 ns <100 ns <25 ns <50 ns 20 MHz <115 ns <60 ns <75 ns <20 ns <40 ns 25 MHz <85 ns <40 ns <55 ns <15 ns <30 ns Propagation delay tPROP is assumed to be 10 ns. 2001 Microchip Technology Inc. DS00778A-page 25 AN778 FIGURE 5-1: PROGRAM MEMORY FETCH TIMING DIAGRAM (16-BIT) Q1 Q2 Q3 Q4 Q1 Q2 OSC1 A<19:16> Address AD<15:0> Address Address Data from External Address 163 150 151 160 162 161 155 166 167 168 ALE 164 169 CS1 CS2 or CSIO 171 171A OE 165 TABLE 5-2: CLKOUT AND I/O TIMING REQUIREMENTS (16-BIT) Param No Symbol 150 TadV2alL 151 Min Typ Max Units Address out valid to ALE (address setup time) 0.25TCY-10 -- -- ns TalL2adl ALE to address out invalid (address hold time) 5 -- -- ns 155 TalL2oeL ALE to OE 10 0.125TCY -- ns 160 TadZ2oeL AD high-Z to OE (bus release to OE) 0 -- -- ns 161 ToeH2adD OE to AD driven 0.125TCY-5 -- -- ns 162 TadV2oeH LS Data valid before OE (data setup time) 20 -- -- ns 163 ToeH2adl OE to data in invalid (data hold time) 0 -- -- ns 164 TalH2alL ALE pulse width -- 0.25TCY -- ns 165 ToeL2oeH OE pulse width 0.5TCY-5 0.5TCY -- ns 166 TalH2alH ALE to ALE (cycle time) -- TCY -- ns 167 TACC Address valid to data valid 0.75TCY-25 -- -- ns 168 TOE OE to data valid -- -- 0.5TCY-25 ns 169 TalL2oeH ALE to OE 0.625TCY-10 -- 0.625TCY+10 ns 171 TalH2csL Chip select active to ALE 0.25TCY-20 -- -- ns 171A TubL2oeH AD valid to chip select active -- -- 10 ns DS00778A-page 26 Characteristics 2001 Microchip Technology Inc. AN778 FIGURE 5-2: PROGRAM MEMORY FETCH TIMING DIAGRAM (8-BIT) Q1 Q2 Q3 Q4 Q1 Q2 OSC1 A<19:8> Address Address 166 150 161 151 AD<7:0> Data Data Address Address 162 162A 163 BA0 170 170A ALE CS1 CS2 or CSIO OE TABLE 5-3: PROGRAM MEMORY FETCH TIMING REQUIREMENTS (8-BIT) Param No Symbol 150 TadV2alL 151 TalL2adl 161 ToeH2adD OE to AD driven 162 TadV2oeH 162A Characteristics Min Typ Max Units Address out valid to ALE (address setup time) 0.25TCY-10 -- -- ns ALE to address out invalid (address hold time) 5 -- -- ns 0.125TCY-5 -- -- ns LS Data valid before OE (data setup time) 20 -- -- ns TadV2oeH MS Data valid before OE (data setup time) 0.25TCY+20 -- -- ns 163 ToeH2adl OE to data in invalid (data hold time) 0 -- -- ns 166 TalH2alH ALE to ALE (cycle time) -- TCY -- ns 170 TubH2oeH BA0 = 0 valid before OE 0.25TCY-10 -- -- ns 170A TubL2oeH BA0 = 1 valid before OE 0.5TCY-10 -- -- ns 2001 Microchip Technology Inc. DS00778A-page 27 AN778 SUMMARY The PIC18C601/801 family of devices provide a flexible external memory interface to support a variety of embedded systems requirements for cost effective implementation with few external components. A multitude of control signals and interface modes make it possible to use a variety of memory devices with ease. The same interface also provides the ability to use memory mapped I/O with a number of peripheral devices. DS00778A-page 28 2001 Microchip Technology Inc. AN778 APPENDIX A: Manufacturer AMD ATMEL INTEL SHARP ST Samsung Catalyst Hyundai Micron SST SUMMARY OF MEMORY DEVICES(1) Part ID Programming Algorithm Family(2) Organization 29F series A x8 29F series A x16 29F series A x8/x16 Remarks Byte x8 Sector Programming B(3) x16 Sector Programming B x8 29 series B 29 series 49 series 49 series B x16 49 series B x8/x16 Byte Byte Boot Block C x8/x16 Strata FLASH/ FLASH File C x8 Strata FLASH/ FLASH File C x8/x16 28F series C x8 28F series C x16 28F series C x8/x16 29F series A x8 29F series A x16 29F series A x8/x16 Word Word Byte FLASH products in this family have multiplexed address/data/command lines and are incompatible with PIC18C601/801 devices. Boot Block FLASH C x8 Bulk Erase FLASH (5) x8 x16 29F series A x8 x 29F series A x8/x16 Byte Boot Block C x8 Boot Block C x8/x16 Even Sectored C x8 Even Sectored C x8/x16 39F series B x8 (3) x8 B x8 29EE series NexFlash (3) Basic Byte/Word Addressing(4) 29F series B Byte Word Sector Programming Note 1: This listing is provided only as an example of typical memory devices available. It is not meant to be exhaustive. 2: Details of each programming algorithm family are provided in Appendix B. 3: For these devices, users must provide all data in the sector. The device will first erase the entire sector, then program it. These devices do not support Sector Erase commands. 4: Applicable only to x8/x16 selectable devices. 5: These devices have a unique set of programming algorithms. They are omitted for the sake of brevity. 2001 Microchip Technology Inc. DS00778A-page 29 AN778 APPENDIX B: PROGRAMMING ALGORITHMS FOR REPRESENTATIVE MEMORY DEVICES(1) Bus Cycles Command Program Cycles Algorithm Needed Read mode/ RESET Read Mfg. ID Read Device ID Write Block Erase Erase Suspend Erase Resume First Addr Second Third Sixth Data Addr Data Addr Data Addr Data Addr Data -- -- -- -- -- -- -- -- -- A 1 X F0 B 1 X F0 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 55 555 90 X00 01 -- -- -- -- -- -- -- C 1 X FF -- A 4 555 AA 2AA B 4 5555 AA 2AAA 55 5555 90 XX00 01 -- C 2 X 90 (IA) (ID) -- -- -- -- -- -- -- -- -- -- -- -- A 4 555 AA 2AA 55 555 90 X01 AD B 4 5555 AA 2AAA 55 5555 90 XX01 20 -- -- -- -- -- -- -- -- -- -- -- C 2 X 90 (IA) (ID) -- A 4 555 AA 2AA 55 555 A0 (WA) (WD) -- -- -- -- A0 (WA) (WD) -- -- -- -- -- -- -- -- -- -- -- B 4 5555 AA 2AAA 55 555 C 2 (WA) 40 (WA) (WD) -- A 6 555 AA 2AA 55 555 80 555 AA 2AA 55 (BA) 30 B 6 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 (BA) 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- C 2 (BA) 20 (BA) D0 -- A 1 X B0 -- -- -- (2) B C 1 X B0 -- -- -- -- -- -- -- -- -- -- A 1 X 30 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- (2) B Sector Protect Verify Fifth Addr -- C Chip Erase Fourth Data 1 X D0 -- -- -- A 6 555 AA 2AA 55 555 80 555 AA 2AA 55 555 10 B 6 5555 AA 2AAA 55 5555 80 5555 AA 2AAA 55 5555 10 C 2 X 30 X D0 -- -- -- -- -- -- -- -- A 4 555 AA 2AA 55 555 90 (SGA) 00/01 -- -- -- -- B 4 5555 AA 2AAA 55 5555 90 (SGA) 00/01 -- -- -- -- C (2) Legend: WA = Write Address, WD = Write Data, IA = Identifier Address, ID = Identifier Data BA = Block Address, SGA = Sector Group Address Note 1: The information provided in this table is for reference only, and is not meant to be a comprehensive description of the device programming algorithms. For complete information, please refer to the manufacturer's data sheet. 2: Instruction unimplemented in this programming algorithm family. DS00778A-page 30 2001 Microchip Technology Inc. Note the following details of the code protection feature on PICmicro(R) MCUs. * * * * * * The PICmicro family meets the specifications contained in the Microchip Data Sheet. Microchip believes that its family of PICmicro microcontrollers is one of the most secure products of its kind on the market today, when used in the intended manner and under normal conditions. There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the PICmicro microcontroller in a manner outside the operating specifications contained in the data sheet. The person doing so may be engaged in theft of intellectual property. Microchip is willing to work with the customer who is concerned about the integrity of their code. Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable". Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our product. If you have any further questions about this matter, please contact the local sales office nearest to you. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, KEELOQ, SEEVAL, MPLAB and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. Total Endurance, ICSP, In-Circuit Serial Programming, FilterLab, MXDEV, microID, FlexROM, fuzzyLAB, MPASM, MPLINK, MPLIB, PICC, PICDEM, PICDEM.net, ICEPIC, Migratable Memory, FanSense, ECONOMONITOR, Select Mode and microPort are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Term Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2001, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified. 2001 Microchip Technology Inc. DS00778A - page 31 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Japan Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Rocky Mountain China - Beijing 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 New China Hong Kong Manhattan Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Austin - Analog 8303 MoPac Expressway North Suite A-201 Austin, TX 78759 Tel: 512-345-2030 Fax: 512-345-6085 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Boston - Analog Unit A-8-1 Millbrook Tarry Condominium 97 Lowell Road Concord, MA 01742 Tel: 978-371-6400 Fax: 978-371-0050 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-6766200 Fax: 86-28-6766599 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Rm. 531, North Building Fujian Foreign Trade Center Hotel 73 Wusi Road Fuzhou 350001, China Tel: 86-591-7557563 Fax: 86-591-7557572 China - Shanghai 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Dayton China - Shenzhen Two Prestige Place, Suite 130 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 Hong Kong Microchip Technology Hongkong Ltd. Unit 901, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 New York India 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O'Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Dallas Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Los Angeles San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Denmark Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 France Arizona Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Arizona Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Germany - Analog Lochhamer Strasse 13 D-82152 Martinsried, Germany Tel: 49-89-895650-0 Fax: 49-89-895650-22 Italy Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 06/01/01 DS00778A-page 32 2001 Microchip Technology Inc.